乙酸镨(III)水合物

乙酸镨(III)水合物 基本信息
CAS号 6192-12-7 分子式 C7H10O6
分子量 190.15100 精确质量  190.04800
PSA  78.90000 LogP  -0.04070

基本信息 展开↓

CAS号:
6192-12-7
3D弹球模型:
立即前往扯扯看
分子式:
C7H10O6
分子量:
190.15100
中文名称:
乙酸镨(III)水合物
英文名称:
praseodymium acetate
中文别名:
乙酸镨(III)水合物;
乙酸镨(III);
醋酸镨
英文别名:
praseodymium acetate;
PRASEODYMIUM ACETATE;
Praseodymium(III) acetate hydrate
精确分子量/精确质量:
190.04800
极性分子表面积/PSA:
78.90000
油水分配系数/LogP:

LogP值指的是某物质在正辛醇/水两相体系中的分配系数的对数值,反映了物质在油水两相中的分配情况。其中、LogP值越大,说明该物质越亲油;反之,LogP值越小,则说明该物质越亲水。
贝尔斯坦号/MDL:
MFCD00150121
EINECS:
228-242-4
InChI:
InChI=1/C22H25N3O2/c1-6-25-18-10-8-7-9-15(18)21-22(25)24-17-12-20(27-14(4)5)19(26-13(2)3)11-16(17)23-21/h7-14H,6H2,1-5H3

生产制备方法及用途展开↓

制备方法


取10g氧化镨(Ⅲ,Ⅳ)(Pr6O11)加至500mL 50%醋酸水溶液中,砂浴中加热。氧化谱在醋酸中溶解极慢,需加热1~2天。(若用氢还原法将其转变为倍半氧化物Pr2O3,则能迅速溶解)。若加热1~2天后仍有少量不溶物,需过滤成清液,将该溶液置于75℃水浴上加热,以蒸去大部分水,冷却,得到黏稠物。将黏稠物转移至玻璃皿中,置于装有颗粒状氢氧化钠及高氯酸镁真空保干器中,抽真空进行干燥,得到水合醋酸镨(Ⅲ)。取10g醋酸镨水合物,放至500mL圆底烧瓶中,加入干燥的DMF 100mL,振摇使醋酸镨尽可能溶解于DMF中(醋酸镨较难溶解)。然后加入无水苯150mL,精馏除去苯 水共沸物。继续蒸馏除去残留的苯和少量DMF,冷却后,Pr(CH3COO)3·DMF析出。用少量干燥乙醚洗涤,置于装有无水氯化钙和五氧化二磷的保干器中储存。最后将晶体置于阿布得哈顿干燥装置中,在210℃下加热以除去DMF,得到无水醋酸镨(Ⅲ)。

合成制备方法


取10g氧化镨(Ⅲ,Ⅳ)(Pr6O11)加至500mL 50%醋酸水溶液中,砂浴中加热。氧化谱在醋酸中溶解极慢,需加热1~2天。(若用氢还原法将其转变为倍半氧化物Pr2O3,则能迅速溶解)。若加热1~2天后仍有少量不溶物,需过滤成清液,将该溶液置于75℃水浴上加热,以蒸去大部分水,冷却,得到黏稠物。将黏稠物转移至玻璃皿中,置于装有颗粒状氢氧化钠及高氯酸镁真空保干器中,抽真空进行干燥,得到水合醋酸镨(Ⅲ)。取10g醋酸镨水合物,放至500mL圆底烧瓶中,加入干燥的DMF 100mL,振摇使醋酸镨尽可能溶解于DMF中(醋酸镨较难溶解)。然后加入无水苯150mL,精馏除去苯水共沸物。继续蒸馏除去残留的苯和少量DMF,冷却后,Pr(CH3COO)3·DMF析出。用少量干燥乙醚洗涤,置于装有无水氯化钙和五氧化二磷的保干器中储存。最后将晶体置于阿布得哈顿干燥装置中,在210℃下加热以除去DMF,得到无水醋酸镨(Ⅲ)。

用途简介


物化性质展开↓

外观与性状:
绿色固体
密度:
1.2g/cm3
沸点:
536.2ºC at 760 mmHg
闪点:
278.1ºC
折射率:
1.618
存储条件/存储方法:

避光,阴凉干燥处,密封保存  

稳定性相关:

常温常压下稳定,绿色水晶颗粒。

溶于水,难溶于乙醇,不溶于吡啶。加热至270℃以上分解。加热至790℃时,生成氧化镨(Ⅲ,Ⅳ)。(Pr6O11)。

与DMF作用,得到Pr(CH3COO)3·DMF,熔点151~155℃,真空加热至210℃,可脱去DMF。与1,10菲咯啉作用[157],得到绿色结晶,加热至270~300℃分解。与硫脲作用,得到熔点为197~198℃绿色结晶,溶于水。与2,2′-联吡啶作用,得到的络合物为绿色晶体,加热至250~260℃分解。

其它信息:

1.       性状:绿色固体,具吸湿性。

2.       密度(g/mL,25℃):未确定

3.       相对蒸汽密度(g/mL,空气=1):未确定

4.       熔点(ºC):151~155

5.       沸点(ºC,常压):未确定

6.       沸点(ºC,23mmHg):未确定

7.       折射率:未确定

8.       闪点(ºF):未确定

9.       比旋光度(º):未确定

10.    自燃点或引燃温度(ºC):未确定

11.    蒸气压(20ºC):未确定

12.    饱和蒸气压(kPa,60ºC):未确定

13.    燃烧热(KJ/mol):未确定

14.    临界温度(ºC):未确定

15.    临界压力(KPa):未确定

16.    油水(辛醇/水)分配系数的对数值:未确定

17.    爆炸上限(%,V/V):未确定

18.    爆炸下限(%,V/V):未确定

19.    溶解性:未确定

安全信息展开↓

危险类别码:
R36/37/38
安全说明:
S26-S36-S37-S39
安全标志:
S26:万一接触眼睛,立即使用大量清水冲洗并送医诊治。
:

合成路线查看所有的合成路线

  • 127-09-3

    无水醋酸钠

  • +

  • 10361-79-2

    氯化镨

  • 6192-12-7

    乙酸镨(III)水合物

毒理性展开↓

毒理学数据:

主要的刺激性影响:

在皮肤上面:刺激皮肤和粘膜

在眼睛上面:刺激的影响

致敏作用:没有已知的敏化现象

生态数据:

 

MSDS 展开↓


Section 1: Product Identification
   Chemical Name:       Praseodymium (III) acetate hydrate (99.9%-Pr) (REO)    
   CAS Registry Number:       6192-12-7    
   Formula:       Pr(OOCCH3)3.XH2O    
   EINECS Number:       none    
   Chemical Family:       metal acetate salt    
   Synonym:       Acetic acid, praseodymium(+3) salt, hydrate    

Section 2: Composition and Information on Ingredients
   Ingredient       CAS Number       Percent       ACGIH (TWA)       OSHA (PEL)    
   Title Compound       6192-12-7       100%       no data       no data    

Section 3: Hazards Identification
   Emergency Overview:       Irritating to skin, eyes and respiratory tract.    
   Primary Routes of Exposure:       Ingestion    
   Eye Contact:       Causes slight to mild irritation of the eyes.    
   Skin Contact:       Causes slight to mild irritation of the skin.    
   Inhalation:       Irritating to the nose, mucous membranes and respiratory tract.    
   Ingestion:       No information on the physiological effects of ingestion.    
   Acute Health Affects:       Irritating to skin, eyes and respiratory tract.    
   Chronic Health Affects:       No information available on long-term chronic effects.    
   NTP:       No    
   IARC:       No    
   OSHA:       No    

SECTION 4: First Aid Measures
   Immediately flush the eyes with copious amounts of water for at least 10-15 minutes. A victim may need
   Eye Exposure:
   assistance in keeping their eye lids open. Get immediate medical attention.
   Wash the affected area with water. Remove contaminated clothes if necessary. Seek medical assistance if
   Skin Exposure:
   irritation persists.
   Remove the victim to fresh air. Closely monitor the victim for signs of respiratory problems, such as difficulty
   Inhalation:
   in breathing, coughing, wheezing, or pain. In such cases seek immediate medical assistance.
   Ingestion:       Seek medical attention immediately. Keep the victim calm. Give the victim water (only if conscious).    

SECTION 5: Fire Fighting Measures
   Flash Point:       not applicable    
   Autoignition Temperature:       none    
   Explosion Limits:       none    
   Extinguishing Medium:       carbon dioxide, dry powder or foam    
   If involved in a fire, fire fighters should be equipped with a NIOSH approved positive pressure self-contained
   Special Fire Fighting Procedures:
   breathing apparatus and full protective clothing.
   Hazardous Combustion and       If involved in a fire this material may emit toxic organic fumes.    
   Decomposion Products:
   Unusual Fire or Explosion Hazards: No unusual fire or explosion hazards.

SECTION 6: Accidental Release Measures
   Spill and Leak Procedures:       Small spills can be mixed with vermiculite or sodium carbonate and swept up.    

SECTION 7: Handling and Storage
   Store in a tightly sealed container in a dry place. If container is left open, salt may adsorb moisture from the
   Handling and Storage:
   atmosphere.

SECTION 8: Exposure Controls and Personal Protection
   Eye Protection:       Always wear approved safety glasses when handling a chemical substance in the laboratory.    
   Skin Protection:       Wear appropriate chemical resistant gloves and protective clothing.    
   Ventilation:       Material may form a fine dust. If possible, handle the material in an efficient fume hood.    
   If in form of fine dust and ventilation is not available a respirator should be worn. The use of respirators
   Respirator:
   requires a Respirator Protection Program to be in compliance with 29 CFR 1910.134.
   Ventilation:       Material may form a fine dust. If possible, handle the material in an efficient fume hood.    
   Additional Protection:       No additional protection required.    

SECTION 9: Physical and Chemical Properties
   Color and Form:       green xtl.    
   Molecular Weight:       318.04    
   Melting Point:       no data    
   Boiling Point:       no data    
   Vapor Pressure:       not applicable    
   Specific Gravity:       no data    
   Odor:       none    
   Solubility in Water:       very soluble    

SECTION 10: Stability and Reactivity
   Stability:       hygroscopic solid    
   Hazardous Polymerization:       no hazardous polymerization    
   Conditions to Avoid:       contact with moisture    
   Incompatibility:       Oxidizing agents and active metals    
   Decomposition Products:       Carbon dioxide, carbon monoxide, organic vapors, and metal oxides and carbonates.    

SECTION 11: Toxicological Information
   RTECS Data:       No information available in the RTECS files.    
   Carcinogenic Effects:       No data available    
   Mutagenic Effects:       No data available    
   Tetratogenic Effects:       No data available    

SECTION 12: Ecological Information
   Ecological Information:       No information available    

SECTION 13: Disposal Considerations
   Disposal:       Dispose of according to local, state and federal regulations.    

SECTION 14: Transportation
   Shipping Name (CFR):       Non-hazardous    
   Hazard Class (CFR):       NA    
   Additional Hazard Class (CFR):       NA    
   Packaging Group (CFR):       NA    
   UN ID Number (CFR):       NA    
   Shipping Name (IATA):       Non-hazardous    
   Hazard Class (IATA):       NA    
   Additional Hazard Class (IATA):       NA    
   Packaging Group (IATA):       NA    
   UN ID Number (IATA):       NA    

SECTION 15: Regulatory Information
   TSCA:       Listed in the TSCA inventory.    
   SARA (Title 313):       Title compound not listed.    
   Second Ingredient:       none    


SECTION 16 - ADDITIONAL INFORMATION
N/A

分子结构与计算化学数据展开↓

分子结构数据


1、摩尔折射率:无可用的

2、摩尔体积(cm3/mol):无可用的

3、等张比容(90.2K):无可用的

4、表面张力(dyne/cm):无可用的

5、介电常数:无可用的

6、极化率(10-24cm3):无可用的

7、单一同位素质量:317.947513Da

8、标称质量:318Da

9、平均质量:318.0397Da

计算化学数据


1、   氢键供体数量:0

2、   氢键受体数量:6

3、   可旋转化学键数量:0

4、   拓扑分子极性表面积(TPSA):120

5、   重原子数量:13

6、   表面电荷:0

7、   复杂度:25.5

8、   同位素原子数量:0

9、   确定原子立构中心数量: 0

10、   不确定原子立构中心数量:0

11、   确定化学键立构中心数量:0

12、   不确定化学键立构中心数量:0

13、   共价键单元数量:4

上下游相关产品

上游产品

更多
  • 127-09-3

    无水醋酸钠

  • 10361-79-2

    氯化镨

立即下载安装“化学加”APP
专业、功能强大,随时调用更加方便