单氟磷酸

单氟磷酸 基本信息
CAS号 13537-32-1 分子式 FH2O3P
分子量 99.98620 精确质量  99.97260
PSA  67.34000 LogP  0.04860

基本信息 展开↓

CAS号:
13537-32-1
3D弹球模型:
立即前往扯扯看
分子式:
FH2O3P
分子量:
99.98620
中文名称:
单氟磷酸
英文名称:
fluorophosphoric acid
中文别名:
单氟磷酸;
氟磷酸;
一氟磷酸
英文别名:
fluorophosphoric acid;
FLUOROPHOSPHORIC ACID;
fluorophosphonic acid
精确分子量/精确质量:
99.97260
极性分子表面积/PSA:
67.34000
油水分配系数/LogP:

LogP值指的是某物质在正辛醇/水两相体系中的分配系数的对数值,反映了物质在油水两相中的分配情况。其中、LogP值越大,说明该物质越亲油;反之,LogP值越小,则说明该物质越亲水。
贝尔斯坦号/MDL:
MFCD00011334
PubChem:
24859463
InChI:
The Key: DWYMPOCYEZONEA-UHFFFAOYSA-N

生产制备方法及用途展开↓

制备方法


将48.467g热的黏稠的偏磷酸倒入一个100mL的铂瓶中,无水HF气体通过冰冷却的铜管冷凝下来,将11.734g液态氟化氢加入到偏磷酸中,使偏磷酸的量比化学计量的量多出5.4%。密封的铂瓶置于室温下于特殊振荡器中振摇7天,得到澄清油状液体,未反应的偏磷酸粘于瓶壁上。纯偏磷酸的制备:由于市售偏磷酸内含有磷酸钠,因此纯偏磷酸用(NH4)2HPO4热分解制得。将此盐放入铂皿内,在加热板上加热直至变成清亮液体,然后将铂皿放入电炉内,加热至500℃。在此温度保持12h,制得纯偏磷酸。

合成制备方法


将48.467g热的黏稠的偏磷酸倒入一个100mL的铂瓶中,无水HF气体通过冰冷却的铜管冷凝下来,将11.734g液态氟化氢加入到偏磷酸中,使偏磷酸的量比化学计量的量多出5.4%。密封的铂瓶置于室温下于特殊振荡器中振摇7天,得到澄清油状液体,未反应的偏磷酸粘于瓶壁上。

纯偏磷酸的制备:由于市售偏磷酸内含有磷酸钠,因此纯偏磷酸用(NH4)2HPO4热分解制得。将此盐放入铂皿内,在加热板上加热直至变成清亮液体,然后将铂皿放入电炉内,加热至500℃。在此温度保持12h,制得纯偏磷酸。

用途简介


物化性质展开↓

密度:
1.83 g/mL at 25 °C
存储条件/存储方法:

常温密闭,阴凉通风干燥

稳定性相关:

常温常压下稳定

避免的物料 氧化物 碱。70℃时固化,在中性或者弱碱性溶液中缓慢水解。纯酸或者浓溶液腐蚀大多数金属和合金,包括不锈钢。对银、铂和铝呈惰性。稀溶液可以腐蚀金属铝和钛。

其它信息:

1.       性状:无色油状液体,中强酸。

2.       密度(g/mL,25/4℃):未确定

3.       相对蒸汽密度(g/mL,空气=1):未确定

4.       熔点(ºC):未确定

5.       沸点(ºC,常压):未确定

6.       沸点(ºC,5.2kPa):未确定

7.       折射率:未确定

8.       闪点(ºC):未确定

9.       比旋光度(º):未确定

10.    自燃点或引燃温度(ºC):未确定

11.    蒸气压(kPa,25ºC):未确定

12.    饱和蒸气压(kPa,60ºC):未确定

13.    燃烧热(KJ/mol):未确定

14.    临界温度(ºC):未确定

15.    临界压力(KPa):未确定

16.    油水(辛醇/水)分配系数的对数值:未确定

17.    爆炸上限(%,V/V):未确定

18.    爆炸下限(%,V/V):未确定

19.    溶解性:未确定

安全信息展开↓

包装等级:
II
风险类别:
8
危险类别码:
R23/24/25:Toxic by inhalation, in contact with skin and if swallowed . R34:Causes burns.
安全说明:
S26-S27-S36/37/39-S45
RTECS号:
TE5000000
安全标志:
S26:万一接触眼睛,立即使用大量清水冲洗并送医诊治。
S27:立刻除去所有污染衣物。
S45:出现意外或者感到不适,立刻到医生那里寻求帮助(最好带去产品容器标签)。
:
危险标志:
T,C

合成路线查看所有的合成路线

  • 7664-38-2

    磷酸

  • +

  • 7664-39-3

    氢氟酸

  • ~58%

  • 13779-41-4

    二氟磷酸

  • +

  • 13537-32-1

    单氟磷酸

  • 96-49-1

    碳酸亚乙酯

  • +

  • 21324-40-3

    六氟磷酸锂

  • 124-38-9

    二氧化碳

  • +

  • 13779-41-4

    二氟磷酸

  • 13478-20-1

    三氟氧化磷

  • +

  • 7664-38-2

    磷酸

  • 13537-32-1

    单氟磷酸

毒理性展开↓

CHEMICAL IDENTIFICATION

RTECS NUMBER :
TE5000000
CHEMICAL NAME :
Phosphorofluoridic acid
CAS REGISTRY NUMBER :
13537-32-1
LAST UPDATED :
199503
DATA ITEMS CITED :
5
MOLECULAR FORMULA :
F-H2-O3-P
MOLECULAR WEIGHT :
99.99
WISWESSER LINE NOTATION :
QPQO&F
毒理学数据:

1、急性毒性:主要的刺激性影响:

在皮肤上面:在皮肤和粘膜上造成腐蚀性影响,刺激皮肤和粘膜;

在眼睛上面:强烈的腐蚀性影响,刺激的影响;没有已知的敏化影响。

生态数据:

通常对水体是稍微有害的,不要将未稀释或大量产品接触地下水,水道或污水系统,未经政府许可勿将材料排入周围环境。

MSDS 展开↓

Name: Fluorophosphoric Acid 70% Material Safety Data Sheet
Synonym: Monofluorophosphoric Acid; Phosphorofluoridic Acid
CAS: 13537-32-1
Section 1 - Chemical Product   MSDS Name:Fluorophosphoric Acid 70% Material Safety Data Sheet
Synonym:Monofluorophosphoric Acid; Phosphorofluoridic Acid

Section 2 - COMPOSITION, INFORMATION ON INGREDIENTS
CAS# Chemical Name content EINECS#
13537-32-1 Fluorophosphoric Acid 70% unlisted
Hazard Symbols: T
Risk Phrases: 23/24/25 34

Section 3 - HAZARDS IDENTIFICATION
  EMERGENCY OVERVIEW
Toxic by inhalation, in contact with skin and if swallowed. Causes burns.Hygroscopic (absorbs moisture from the air).Corrosive.
Potential Health Effects
Eye:
Causes eye burns. May cause chemical conjunctivitis and corneal damage.
Skin:
Causes skin burns. May cause skin rash (in milder cases), and cold and clammy skin with cyanosis or pale color.
Ingestion:
May cause severe and permanent damage to the digestive tract. Causes gastrointestinal tract burns. May cause perforation of the digestive tract. The toxicological properties of this substance have not been fully investigated. May cause systemic effects.
Inhalation:
May cause irritation of the respiratory tract with burning pain in the nose and throat, coughing, wheezing, shortness of breath and pulmonary edema. Causes chemical burns to the respiratory tract.
Inhalation may be fatal as a result of spasm, inflammation, edema of the larynx and bronchi, chemical pneumonitis and pulmonary edema.
Aspiration may lead to pulmonary edema. May cause systemic effects.
Chronic:
Effects may be delayed.

Section 4 - FIRST AID MEASURES
  Eyes: Get medical aid immediately. Do NOT allow victim to rub eyes or keep eyes closed. Extensive irrigation with water is required (at least 30 minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Do not induce vomiting. If victim is conscious and alert, give 2-4 cupfuls of milk or water. Get medical aid immediately. Wash mouth out with water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical aid. Do NOT use mouth-to-mouth resuscitation. If breathing has ceased apply artificial respiration using oxygen and a suitable mechanical device such as a bag and a mask.
Notes to Physician:

Section 5 - FIRE FIGHTING MEASURES
  General Information:
As in any fire, wear a self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or equivalent), and full protective gear. During a fire, irritating and highly toxic gases may be generated by thermal decomposition or combustion. Use water spray to keep fire-exposed containers cool. Vapors may be heavier than air. They can spread along the ground and collect in low or confined areas. Containers may explode when heated.
Extinguishing Media:
Use dry chemical. Cool containers with flooding quantities of water until well after fire is out.

Section 6 - ACCIDENTAL RELEASE MEASURES
  General Information: Use proper personal protective equipment as indicated in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth), then place in suitable container. Avoid runoff into storm sewers and ditches which lead to waterways. Clean up spills immediately, observing precautions in the Protective Equipment section. Provide ventilation.

Section 7 - HANDLING and STORAGE
  Handling:
Keep container tightly closed. Do not get on skin or in eyes. Do not ingest or inhale. Use with adequate ventilation. Use and store under nitrogen. Use only in a chemical fume hood. Discard contaminated shoes.
Storage:
Store in a cool, dry place. Store in a tightly closed container.
Corrosives area. Store protected from moisture.

Section 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION
  Engineering Controls:
Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower. Use adequate ventilation to keep airborne concentrations low.
Exposure Limits CAS# 13537-32-1: Personal Protective Equipment Eyes: Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHA's eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin exposure.
Clothing:
Wear appropriate protective clothing to minimize contact with skin.
Respirators:
A respiratory protection program that meets OSHA's 29 CFR 1910.134 and ANSI Z88.2 requirements or European Standard EN 149 must be followed whenever workplace conditions warrant respirator use.

Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
 
Physical State: Liquid
Color: colorless
Odor: pungent odor
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: None.
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: soluble
Specific Gravity/Density: 1.8300g/cm3
Molecular Formula: H2PO3F
Molecular Weight: 99.99

Section 10 - STABILITY AND REACTIVITY
  Chemical Stability:
Stable at room temperature in closed containers under normal storage and handling conditions.
Conditions to Avoid:
Incompatible materials, moisture, excess heat, exposure to moist air or water.
Incompatibilities with Other Materials:
Moisture, strong bases, strong oxidizing agents.
Hazardous Decomposition Products:
Phosphine, irritating and toxic fumes and gases, hydrogen fluoride gas.
Hazardous Polymerization: Has not been reported

Section 11 - TOXICOLOGICAL INFORMATION
  RTECS#:
CAS# 13537-32-1: TE5000000 LD50/LC50:
Not available.
Carcinogenicity:
Fluorophosphoric Acid - Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.

Section 12 - ECOLOGICAL INFORMATION
 

Section 13 - DISPOSAL CONSIDERATIONS
  Dispose of in a manner consistent with federal, state, and local regulations.

Section 14 - TRANSPORT INFORMATION
 
IATA
Shipping Name: FLUOROPHOSPHORIC ACID, ANHYDROUS
Hazard Class: 8
UN Number: 1776
Packing Group: II
IMO
Shipping Name: FLUOROPHOSPHORIC ACID, ANHYDROUS
Hazard Class: 8
UN Number: 1776
Packing Group: II
RID/ADR
Shipping Name: FLUOROPHOSPHORIC ACID, ANHYDROUS
Hazard Class: 8
UN Number: 1776
Packing group: II

Section 15 - REGULATORY INFORMATION
 
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: T
Risk Phrases:
R 23/24/25 Toxic by inhalation, in contact with skin
and if swallowed.
R 34 Causes burns.
Safety Phrases:
S 28A After contact with skin, wash immediately with
plenty of water.
S 36/37/39 Wear suitable protective clothing, gloves
and eye/face protection.
S 38 In case of insufficient ventilation, wear
suitable respiratory equipment.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 13537-32-1: No information available.
Canada
None of the chemicals in this product are listed on the DSL/NDSL list.
CAS# 13537-32-1 is listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 13537-32-1 is not listed on the TSCA inventory.
It is for research and development use only.


SECTION 16 - ADDITIONAL INFORMATION
N/A

分子结构与计算化学数据展开↓

分子结构数据


1、   摩尔折射率:12.15

2、   摩尔体积(cm3/mol):53.1

3、   等张比容(90.2K):147.2

4、   表面张力(dyne/cm):58.9

5、   极化率(10-24cm3):4.81

计算化学数据


1、   疏水参数计算参考值(XlogP):-1.1

2、   氢键供体数量:2

3、   氢键受体数量:4

4、   可旋转化学键数量:0

5、   拓扑分子极性表面积(TPSA):57.5

6、   重原子数量:5

7、   表面电荷:0

8、   复杂度:61.3

9、   同位素原子数量:0

10、   确定原子立构中心数量:0

11、   不确定原子立构中心数量:0

12、   确定化学键立构中心数量:0

13、   不确定化学键立构中心数量:0

14、   共价键单元数量:1

上下游相关产品

上游产品

更多
  • 7664-38-2

    磷酸

  • 7664-39-3

    氢氟酸

  • 21324-40-3

    六氟磷酸锂

  • 14456-60-1

    difluorophosphoric acid anhydride

  • 403-65-6

    [fluoro(phenoxy)phosphoryl]oxybenzene

下游产品

更多
  • 13779-41-4

    二氟磷酸

  • 7664-38-2

    磷酸

立即下载安装“化学加”APP
专业、功能强大,随时调用更加方便