4-二乙基水杨醛

4-二乙基水杨醛 基本信息
CAS号 13573-08-5 分子式 GeH2I2
分子量 328.46500 精确质量  329.74600
PSA  0.00000 LogP  1.61560

基本信息 展开↓

CAS号:
13573-08-5
3D弹球模型:
立即前往扯扯看
分子式:
GeH2I2
分子量:
328.46500
中文名称:
4-二乙基水杨醛
英文名称:
Germanium iodide (GeI2)
中文别名:
4-二乙基水杨醛;
二碘化锗;
二碘化锗(II);
碘化锗(II)
英文别名:
Germanium iodide (GeI2);
GERMANIUM(II) IODIDE;
Germanium(II) iodide;
diiodogermanium
精确分子量/精确质量:
329.74600
极性分子表面积/PSA:
0.00000
油水分配系数/LogP:

LogP值指的是某物质在正辛醇/水两相体系中的分配系数的对数值,反映了物质在油水两相中的分配情况。其中、LogP值越大,说明该物质越亲油;反之,LogP值越小,则说明该物质越亲水。
贝尔斯坦号/MDL:
MFCD00135537
EINECS:
236-998-1
PubChem:
24863948
InChI:
The Key: IAGYEMVJHPEPGE-UHFFFAOYSA-N

生产制备方法及用途展开↓

制备方法


1.将10g一硫化锗粉碎,放入250mL锥形烧瓶中,同时加入过量200%(约80mL)的浓氢碘酸(57%,相对密度1.7)。烧瓶口用玻璃棉堵塞,在水蒸气浴上加热至100℃,并不断摇动,使其反应。约20min后,在古氏过滤器中装入玻璃棉,趁热过滤,自然冷却滤液,即生成有光泽的黄棕色二碘化锗片状结晶。结晶完全析出以后(约30min),用玻璃过滤器过滤,收集结晶,含有硫化锗的滤液重新倒入原来的锥形瓶中。将此操作过程反复3~4次,大部分硫化物就可变为碘化物。因为其中含有少量四碘化锗,将结晶夹在滤纸间挤压以除去水分,在真空中加热至100℃,使四碘化锗升华除去。所得到的二碘化锗放在密封管中保存。 2.把20g四碘化锗装入250mL三口烧瓶中,在三个口上分别安装回流冷凝器、搅拌器、玻璃塞。投入10mL浓氢碘酸(57%)及20mL水,搅拌。再加入7.6mL 50%次磷酸,将烧瓶加塞。将该混合物在回流下煮沸。在短时间内,红色四碘化锗结晶就转变为二碘化锗的黄色片状结晶,用稀氢碘酸洗涤二碘化锗结晶,将结晶放到阿布德哈登[Abderhalden]干燥器中的五氧化二磷上面,抽真空,在甲苯沸点110℃进行干燥。

合成制备方法


1.将10g一硫化锗粉碎,放入250mL锥形烧瓶中,同时加入过量200%(约80mL)的浓氢碘酸(57%,相对密度1.7)。烧瓶口用玻璃棉堵塞,在水蒸气浴上加热至100℃,并不断摇动,使其反应。约20min后,在古氏过滤器中装入玻璃棉,趁热过滤,自然冷却滤液,即生成有光泽的黄棕色二碘化锗片状结晶。结晶完全析出以后(约30min),用玻璃过滤器过滤,收集结晶,含有硫化锗的滤液重新倒入原来的锥形瓶中。将此操作过程反复3~4次,大部分硫化物就可变为碘化物。因为其中含有少量四碘化锗,将结晶夹在滤纸间挤压以除去水分,在真空中加热至100℃,使四碘化锗升华除去。所得到的二碘化锗放在密封管中保存。

2.把20g四碘化锗装入250mL三口烧瓶中,在三个口上分别安装回流冷凝器、搅拌器、玻璃塞。投入10mL浓氢碘酸(57%)及20mL水,搅拌。再加入7.6mL 50%次磷酸,将烧瓶加塞。将该混合物在回流下煮沸。在短时间内,红色四碘化锗结晶就转变为二碘化锗的黄色片状结晶,用稀氢碘酸洗涤二碘化锗结晶,将结晶放到阿布德哈登[Abderhalden]干燥器中的五氧化二磷上面,抽真空,在甲苯沸点110℃进行干燥。

用途简介


物化性质展开↓

外观与性状:
黄色至金色片或粉末
密度:
5.73 g/cm3
熔点:
460 °C
沸点:
545°C
存储条件/存储方法:

常温密闭,阴凉通风干燥

稳定性相关:

常温常压下稳定

避免的物料 水分/潮湿  氧化物  光  .遇湿空气即水解,在干燥空气中稳定。在氨溶液中就生成亚胺锗。二碘化锗稍溶于冷的氢碘酸,加热就非常易溶,所以能够重结晶。在真空中于240℃升华。二碘化锗可用作有机锗化物的合成原料。

其它信息:

1.       性状:具有黄棕色光泽的六方晶系片状结晶。

2.       密度(g/mL,25/4℃):5.37

3.       相对蒸汽密度(g/mL,空气=1):未确定

4.       熔点(ºC):未确定

5.       沸点(ºC,常压):未确定

6.       沸点(ºC,5.2kPa):未确定

7.       折射率:未确定

8.       闪点(ºC):未确定

9.       比旋光度(º):未确定

10.    自燃点或引燃温度(ºC):不适用的

11.    蒸气压(kPa,25ºC):未确定

12.    饱和蒸气压(kPa,60ºC):未确定

13.    燃烧热(KJ/mol):未确定

14.    临界温度(ºC):未确定

15.    临界压力(KPa):未确定

16.    油水(辛醇/水)分配系数的对数值:未确定

17.    爆炸上限(%,V/V):未确定

18.    爆炸下限(%,V/V):未确定

19.    溶解性:分解

安全信息展开↓

包装等级:
II
风险类别:
8
WGK_Germany:
3
德国有关水污染物质的分类清单
危险类别码:
R34
安全说明:
S23-S26-S27-S36/37/39-S45
安全标志:
S23:不要吸入蒸汽。
S26:万一接触眼睛,立即使用大量清水冲洗并送医诊治。
S27:立刻除去所有污染衣物。
S45:出现意外或者感到不适,立刻到医生那里寻求帮助(最好带去产品容器标签)。
:
危险标志:
C: Corrosive;

合成路线查看所有的合成路线

  • 7440-56-4

  • +

  • 7553-56-2

  • 13573-08-5

    4-二乙基水杨醛

毒理性展开↓

毒理学数据:

1、急性毒性:主要的刺激性影响:

在皮肤上面:在皮肤和粘膜上造成腐蚀性影响,刺激皮肤和粘膜;

在眼睛上面:强烈的腐蚀性影响,刺激的影响;没有已知的敏化影响。

生态数据:

通常对水体是稍微有害的,不要将未稀释或大量产品接触地下水,水道或污水系统,未经政府许可勿将材料排入周围环境。

MSDS 展开↓


Section 1: Product Identification
   Chemical Name:       Germanium (II) iodide (99.99+%-Ge) PURATREM    
   CAS Registry Number:       13573-08-5    
   Formula:       GeI2    
   EINECS Number:       236-998-1    
   Chemical Family:       metal halide    
   Synonym:       Germanium diiodide    

Section 2: Composition and Information on Ingredients
   Ingredient       CAS Number       Percent       ACGIH (TWA)       OSHA (PEL)    
   Title Compound       13573-08-5       100%       no data       no data    

Section 3: Hazards Identification
   Severe irritant to skin, eyes and respiratory tract. Material hydrolyzes in contact with moisture releasing
   Emergency Overview:
   hydroiodic acid and under some conditions corrosive hydrogen iodide vapors.
   Primary Routes of Exposure:       Ingestion, inhalation, skin, eyes    
   Eye Contact:       Causes severe irritation to the eyes.    
   Skin Contact:       Causes severe irritation of the skin with redness, pain, itching, pimples, boils, hives and blisters.    
   Forms hydroiodic acid in the presence of moisture. Inhalation of vapors leads to irritation of the respiratory
   Inhalation:
   tract.
   Ingestion:       Severe irritation of the Gastrointestinal system may occur.    
   Acute Health Affects:       Irritating to skin, eyes and respiratory tract. May cause dyspnea (breathing difficulty), and pulmonary edema.    
   Chronic ingestion of iodides may produce iodism. Symptoms include skin rash, running nose, headache and
   Chronic Health Affects:
   irritation of mucous membranes.
   NTP:       No    
   IARC:       No    
   OSHA:       No    

SECTION 4: First Aid Measures
   Immediately flush the eyes with copious amounts of water for at least 10-15 minutes. A victim may need
   Eye Exposure:
   assistance in keeping their eye lids open. Get immediate medical attention.
   Wash the affected area with water. Remove contaminated clothes if necessary. Seek medical assistance if
   Skin Exposure:
   irritation persists.
   Remove the victim to fresh air. Closely monitor the victim for signs of respiratory problems, such as difficulty
   Inhalation:
   in breathing, coughing, wheezing, or pain. In such cases seek immediate medical assistance.
   Seek medical attention immediately. Keep the victim calm. Give the victim water (only if conscious). Induce
   Ingestion:
   vomiting only if directed by medical personnel.

SECTION 5: Fire Fighting Measures
   Flash Point:       not applicable    
   Autoignition Temperature:       none    
   Explosion Limits:       none    
   Extinguishing Medium:       none required    
   If involved in a fire, fire fighters should be equipped with a NIOSH approved positive pressure self-contained
   Special Fire Fighting Procedures:
   breathing apparatus and full protective clothing.
   Hazardous Combustion and       If involved in a fire this material may emit corrosive hydrogen fluoride fumes.    
   Decomposion Products:
   Unusual Fire or Explosion Hazards: No unusual fire or explosion hazards.

SECTION 6: Accidental Release Measures
   To avoid raising dust, small spills can be mixed with powdered sodium bicarbonate, lime, or calcium carbonate
   Spill and Leak Procedures:
   and swept up.

SECTION 7: Handling and Storage
   Store material in a tightly sealed bottle away from moisture. If possible, handle material in an efficient fume
   Handling and Storage:
   hood. Prolonged exposure to the atmosphere may lead to degradation of the product.

SECTION 8: Exposure Controls and Personal Protection
   Eye Protection:       Always wear approved safety glasses when handling a chemical substance in the laboratory.    
   Skin Protection:       Wear appropriate chemical resistant gloves and protective clothing.    
   Ventilation:       If possible, handle the material in an efficient fume hood.    
   If in form of fine dust and ventilation is not available a respirator should be worn. The use of respirators
   Respirator:
   requires a Respirator Protection Program to be in compliance with 29 CFR 1910.134.
   Ventilation:       If possible, handle the material in an efficient fume hood.    
   Additional Protection:       No additional protection required.    

SECTION 9: Physical and Chemical Properties
   Color and Form:       -10 mesh yellow pwdr.    
   Molecular Weight:       326.4    
   Melting Point:       dec.    
   Boiling Point:       no data    
   Vapor Pressure:       no data    
   Specific Gravity:       5.73    
   Odor:       not determined    
   Solubility in Water:       Decomposes in water    

SECTION 10: Stability and Reactivity
   Stability:       moisture sensitive    
   Hazardous Polymerization:       no hazardous polymerization    
   Conditions to Avoid:       contact with moisture    
   Incompatibility:       Oxidizing agents, halogens and active metals    
   Decomposition Products:       with moisture: hydroiodic acid and germanium oxides    

SECTION 11: Toxicological Information
   RTECS Data:       No information available in the RTECS files.    
   Carcinogenic Effects:       no data    
   Mutagenic Effects:       no data    
   Tetratogenic Effects:       no data    

SECTION 12: Ecological Information
   Ecological Information:       No information available    

SECTION 13: Disposal Considerations
   Disposal:       Dispose of according to local, state and federal regulations.    

SECTION 14: Transportation
   Shipping Name (CFR):       Non-hazardous    
   Hazard Class (CFR):       NA    
   Additional Hazard Class (CFR):       NA    
   Packaging Group (CFR):       NA    
   UN ID Number (CFR):       NA    
   Shipping Name (IATA):       Non-hazardous    
   Hazard Class (IATA):       NA    
   Additional Hazard Class (IATA):       NA    
   Packaging Group (IATA):       NA    
   UN ID Number (IATA):       NA    

SECTION 15: Regulatory Information
   TSCA:       Listed in the TSCA inventory.    
   SARA (Title 313):       Title compound not listed    
   Second Ingredient:       none    


SECTION 16 - ADDITIONAL INFORMATION
N/A

分子结构与计算化学数据展开↓

分子结构数据


1、摩尔折射率:无可用的

2、摩尔体积(cm3/mol):无可用的

3、等张比容(90.2K):无可用的

4、表面张力(dyne/cm):无可用的

5、介电常数:无可用的

6、极化率(10-24cm3):无可用的

7、单一同位素质量:329.745748 Da

8、标称质量:330 Da

9、平均质量:328.4648 Da

计算化学数据


1.疏水参数计算参考值(XlogP):无

2.氢键供体数量:0

3.氢键受体数量:0

4.可旋转化学键数量:0

5.互变异构体数量:无

6.拓扑分子极性表面积0

7.重原子数量:3

8.表面电荷:0

9.复杂度:2.8

10.同位素原子数量:0

11.确定原子立构中心数量:0

12.不确定原子立构中心数量:0

13.确定化学键立构中心数量:0

14.不确定化学键立构中心数量:0

15.共价键单元数量:1

上下游相关产品

上游产品

更多
  • 7440-56-4

  • 7553-56-2

下游产品

更多
  • 591-50-4

    碘苯

  • 92-52-4

    联苯

  • 2816-43-5

    三苯基氢化锗

  • 1048-05-1

    四苯基锗

  • 5764-63-6

    1,1-diiodo-3,4-dimethyl-2,5-dihydrogermole

立即下载安装“化学加”APP
专业、功能强大,随时调用更加方便